DAQ-801 and DAQ-802 from $295
Low Cost 12-Bit Data Acquisition Boards for IBM's or Compatibles
- 40 KHz Sampling Rate with True 12-Bit Resolution
- Eight Channel Single-Ended or Differential
- Channel Scan Capability with Various Gain for Each Channel
- 1024 x 16 FIFO Data Buffer
- Programmable Gain of 1, 10, 100 and 1000 for DAQ-801 and 1, 2, 4, and 8 for DAQ-802
- Two 12-Bit D/A Channels, One 16-Bit
Timer/Counter and
32-Bit Digital I/O
- Interrupt Handling Capability
OMEGAÆs DAQ-801/802 is a low cost data acquisition system with 12-bit resolution, eight channel analog input, two channel D/A output, 32-bit digital I/O, and one 16-bit programmable timer/counter for ISA bus computers (IBM PC/AT or compatible). The maximum sampling rate is 40 KHz for A/D with internal or external triggering.
The DAQ-801/802 offers software selectable eight channel single-ended or differential analog inputs with 12-bit resolution. The input voltage can be either unipolar or bipolar, and is jumper selectable. DAQ-801 provides programmable gains of 1, 10, 100, and 1000. The DAQ-802 has programmable gains of 1, 2, 4 and 8. Both the DAQ-801 and DAQ-802 have auto zeroing and self-calibrating facility for A/D conversion. The main D-37 connector on the board accessed through the rear of the PC is for analog I/O, control lines and 8-bit digital I/O. A second auxiliary D-37 connector is provided for the additional 24 digital I/O lines from an 8255 programmable peripheral interface chip.
There is a 1024 sample data FIFO available which provides a cushion for the data stream coming from the output of the A/D converter. This protects data integrity when using an interrupt routine under Windows or other operating systems. SCAN LIST capability is also provided for scanning the input channels with their corresponding gains. Sequential scanning between any two channels can be programmed.
The DAQ-801/802 can be installed in any available I/O base address location without conflict with presently installed devices. The board can be enabled or disabled through software manipulation. The interrupt levels are register selectable through software from IRQ 2-7, 10-12, 14 and 15. The 24 digital I/O lines for the second D-37 connector are directly from an 8255 programmable peripheral interface chip.
SOFTWARE:
The DAQ-800 is supplied with DaqEZ software. DaqEZ is a Windows application which provides real-time data display and datalogging to disk. Once the data is stored to disk, it may be imported to spread sheet and other data analysis programs. Also supplied are software drivers.
The software drivers provide support for various programming languages such as Microsoft C/C++, QuickBasic, and Turbo Pascal. A dynamic link library (DLL) is furnished for programming most languages under Microsoft Windows. As an option, Visual Basic Controls (VBX) called VISUALDAQ are also available for only $195.
DAQ-800 boards are supported by Labtech Notebook and Snapmaster Software.
UIO-37:
Both the main analog I/O connector and the auxiliary digital I/O connector use a standard male 37 pin D-type format. For easy field wiring to these connectors the UIO-37 terminal panel may be used. One UIO-37 is needed for each connector. A CP-DAQ cable is also required to connect each UIO-37 to the DAQ-800.
SPECIFICATIONS
ANALOG INPUT:
Maximum Sampling Rate: 40 KHz (all gains)
Channels:8 differential
Input Ranges: ▒5V
Accuracy
Gain <1000: 0.05% FS (typical), 0.25% FS (maximum)
Gain = 1000: 0.1% FS (typical), 1.0% FS (maximum)
Output Data Codes: Twos complement
GAIN RANGES:
Mode 801: 1, 10, 100, 1000
Mode 802: 1, 2, 4, 8
Input Impedance: 1M ₧
Input Bias Current: 50 pA
Surge Protection Up To: ▒20 V
Resolution: 12-bit + sign
CONVERSATION TIME:
With Auto Zeroing: 15.2 ms
Without Auto Zeroing: 25.6 ms
Convert Type: Successive approximation
Size of Scan List: 8 samples
Zero Error: Adjustable to 0
Gain Error: Adjustable to 0
ANALOG OUTPUT:
Channels: 2v
Output Ranges: 0-5 V, 0-10 V, ▒5 V, ▒10 V (jumper selectable)
Output Data Coding: Straight binary
Resolution: 12-bits
DIGITAL I/O (8 bits on main D-37 connector):
Output Bits: 4
Low/High Voltage: 0.4/3.8 V
Source/Sink Current: 0.5/2.5 mA
Input Bits: 4 TTL compatible
Timer/Counters
Number of Counters: 1, down
Type: 82C54
DIGITAL I/O (24 bits on auxiliary connector):
Type: CMOS 8255A
I/O: 24 bits
POWER REQUIREMENTS:
+5 Vdc: 750 mA typ, 900 mA max
-5 Vdc: 15 mA typ, 20 mA max
v+12 Vdc: 60 mA typ, 80 mA max
-12 Vdc: 60 mA typ, 80 mA max
ENVIRONMENTS:
Operating Temperature: 0 to 70░C
Interrupt Level: 3-7, 9-12, 14, 15
Humidity: 0 to 95%
Dimensions
Long: 7" (18 cm)
High: 4.8" (12 cm)
CONNECTORS:
The analog inputs and eight digital I/O are connected through a male 37-pin D-type connector at the
rear of the computer. An auxiliary male D-37 connector is employed to support additional 24-bit digital I/O.
COPY [To Your Hard Drive] DaqSuite software now! (includes DaqEZ Windows application and software drivers)
VIEW an Adobe Acrobat pdf file for more product info (requires Acrobat Reader).
VIEW the DAQ-800 operator's manual now! (requires Acrobat Reader).
VIEW the Daqdrive Software manual now! (requires Acrobat Reader).
VIEW the Daqdrive Supplemental manual now! (requires Acrobat Reader).
![Sales and Service 1.800.826.6342](/file/20394/OMEGA and Dilbert Too!.iso/Omega/OMEGA/PRODUCTS/IMAGES/WEBSERVC.GIF)
U.S.A. and Canada
|
|
International Callers;
Sales and Service; 203.359.1660
|
|
Please E-Mail any comments
or suggestions to OMEGA®.
![www.omega.com](/file/20394/OMEGA and Dilbert Too!.iso/Omega/OMEGA/PRODUCTS/IMAGES/OMSMLBEV.GIF)
® COPYRIGHT 1999
OMEGA
ENGINEERING, INC. ALL RIGHTS RESERVED |
|